Adjusting the Cable

Adjusting the Cable On Renegade Hoof Boots

For Cable Change video, go here —>Cable Change Video

For info on changing a cable go here —>Cable Change Page


When the boot is installed upon the hoof, and with the toe strap properly tensioned as explained on the Installing the Boot page, the preferred amount of strap extending past the black rubber keeper loop is from 1/2" to 3/4" like shown in the photo above.

If the strap extends less than 1/2", then the strap is prone to being pulled loose when riding in deep footing or heavy brush.

If the strap extends past the loop more than 3/4" as shown in the photo below, the contact surface area of the gripping portion of the strap will be reduced. This can lead to a reduction in the holding power of the strap.

Correspondingly, the gap between the Cable Adapter (the cylindrical, shiny, aluminum part that connects the cable to the Tension Strap) and the Lateral Cable Guide Block (the protrusion on the side of the boot shell that has two holes in it) should also be at least 3/4". If this gap is less than 1/2" then it may be difficult to be able to easily pull the Heel Captivator well up onto the heel bulbs. Worse yet, under extreme load they may interfere with each other, changing the angle of engagement, loading the cables individual strands unevenly resulting in failure of overloaded strands, followed by the rest of the strands.

Cable Adjustment on the Renegade Hoof Boot

Additionally, make sure that when you initially tighten the strap, you are doing so based on feel and not on any goal as to where you want the end of the strap to be. In other words, don't pull the strap extra tight or make it extra loose in order to comply with the recommended end position specifications.

The strap will end up where the strap ends up based solely on the amount of force you use to tension it as described in the Installing the Boot page. If the strap end-position is out of parameter then proceed with the cable adjustment sequence below.

Cable Adjustment on the Renegade Hoof Boot

Begin by unfastening the tension strap

Cable Adjustment on the Renegade Hoof Boot

Notice the Marker Dimples on the boot and the red Paint Dot on the cable. These will be your reference marks for making the adjustment. Moving the cable toward the cable clamp will effectively shorten the cable setting and reduce the amount of strap end length and vice versa.

The Cables are designed so that if necessary, a cable adjustment outward can be performed even to the extent that the Paint Dot on the cable can only just barely be visible as it disappears into the Lateral Cable Guide Block.

Cable Adjustment on the Renegade Hoof Boot

Using a small flat screwdriver or other pointy tool, pry out the cable clamp just enough to expose the top edge like shown below. New Method: Since these photos were taken, the Cable Clamp has been updated with an "easy pry" hole on the exposed face of the Cable Clamp. To use, simply stick the long end of the supplied L-wrench into this hole and rotate the L-wrench down, consequently also rotating the top of the Cable Clamp outward to expose the set screws.

Cable Adjustment on the Renegade Hoof Boot

Now you have access to the two set screws which are responsible for locking the cables into position. Do not rotate the cable clamp outward any further than needed to expose the set screws.

Cable Adjustment on the Renegade Hoof Boot

Using the supplied 1/16" L-wrench or a purchased Pro Hex wrench, back the set-screws out about 2-1/2 full turns which in most cases is sufficient to release the cable for adjustment. Leaving the set screws in place like this reduces the risk of losing these small screws and can save time. However, this will not allow the Cable Clamp to rotate back into its original position and at times will not allow the cable to move easily if at all. This is due to the offset between the Cable Clamp Cable-Guideway and the Boot Shell Cable-Guideways which can pinch the Cable. To avoid this, it is recommended to remove the set screws completely, save them in a cup so as not to lose them, and rotate the Cable Clamp fully back into its original position. This will ensure the Cable will slide smoothly without binding.

Cable Adjustment on the Renegade Hoof Boot

The cables are now loose and free to move which means you must be careful to not pull them out accidentally as they can be a bugger to get back in if not experienced. If you accidentally pull the cables out, review the Cable Change Page

Cable Adjustment on the Renegade Hoof Boot

For the sake of clarity, I have cut away part of the boot material to expose the hidden cable pathways and the cable ends. Visible are the two individual cables (one from the left side and one from the right side) which overlap each other at the cable clamp.

In order to shorten the effective length of each cable, you will be resetting the end of each cable by pushing the end further through the cable clamp or vice versa. Another view is shown below.

Cutaway Clamp

Another cutaway view.

Renegade Hoof Boots Cutaway Clamp

There are two methods for moving the cables. One method is to push an outward bulging loop in the cable like this.

Cable Adjustment on the Renegade Hoof Boot

Then press inward on the loop which will cause the end of the cable to move on through the cable clamp.

Cable Adjustment on the Renegade Hoof Boot

The trick is to keep pushing the Cable Adapter and the Heel Captivator together.

Cable Adjustment on the Renegade Hoof Boot

An alternative method is to use needle nose pliers or hemostats for moving the cable. Be careful not to use too much pressure or force as this may damage the cable.

Cable Adjustment on the Renegade Hoof Boot

Adjust as necessary and repeat for the other side. In most cases, the cable will only need to be moved one or two marks. If you need to move the cable three marks or more, this is an indication that you may need a different size boot.

Should you have trouble moving the cables as demonstrated above, remove the set-screws entirely and push the cable clamp back into it's home position as previously discussed in step 7. This will allow the cables to have their maximum looseness so be extra carefull not to pull the cables out. If you accidentally pull the cables out, review the Cable Change Page.

Cable Adjustment on the Renegade Hoof Boot

Shown set to the third mark.

Cable Adjustment on the Renegade Hoof Boot

The picture does not show this but it is best to rotate the Cable Clamp out a full 90 degrees so that the set screws are facing directly outward. This will best ensure that the Cables lay side by side relative to the set screws so that the set screws apply pressure evenly between each of the two cables. Now re-tighten the set screws but do this by tightening one screw a little bit then the other screw a little bit, back and forth a few times. In this way you will seat the cables under the screws more evenly than just cranking them down in one step.

Cable Adjustment on the Renegade Hoof Boot

Be sure to tighten the set screws well. Insufficiently torqued set screws may result in the boot base becoming detached from the Heel Captivator en route, possibly even never to be seen again. When tightening, you should be able to feel the resistance increase slightly as the set screws make contact with and begin to compress the cables. Continue about 1/2 to 1 more turn until you feel the set screws stop when the cables are just about fully compressed. Apply just a tad more torque to each set screw to be sure they are snug.

Cable Adjustment on the Renegade Hoof Boot

Push the cable clamp back into its home position.

Cable Adjustment on the Renegade Hoof Boot

You are now finished with the cable adjustment so put the boot back on your horse and check the new strap position.

Cable Adjustment on the Renegade Hoof Boot

Insert the Philips head screw and you are finished! If you have trouble with any of these steps, please contact us for further assistance.

Changing the cable on the Renegade Hoof Boot Step 24